歡迎來訪濟南共潤科技有限公司官網!

濟南共潤科技有限公司

咨詢服務熱線
0531-88270327 13153168609
當前位置: 首頁 - 新聞中心 >
新聞中心

導軌絲杠廠家來告訴你直線導軌安裝情況介紹!

來源:http://www.phkcgc.live/ 日期:2018-12-07 發布人:admin

直線導軌是一種翻滾傳動部件,它由鋼珠在滑塊與導軌之間作無限翻滾循環,使得負載渠道能沿著導軌輕易的以高精度作線性運動。

Linear guideway is a rolling transmission component, which makes infinite rolling cycle between slider and guideway by steel balls, so that the load channel can move along the guideway easily and linearly with high precision.
直線導軌前期裝置作業介紹如下:
The operation of the pre-installation of the linear guide is described as follows:
機臺水平的校對。
Verification of machine level.
用兩個等高量塊和一大理石量尺放在裝置基面上,放上精密的水平儀調試底座水平。
Two equal-height blocks and a marble gauge are placed on the base of the device, and a precise level meter is placed to adjust the base level.
直線導軌裝置基面粗糙度,平面度,直線度以及外觀的查看。
Check the roughness, flatness, straightness and appearance of the base surface of the linear guide device.
直線導軌裝置基面與導軌側基準裝置面的倒角處理。
The chamfering treatment between the base plane of the linear guide device and the base plane of the guide rail side.
倒角半徑小于或等于3.5mm,若發現倒角過大或凸出,應及時選用油石和銼刀處理,否則會形成導軌精度的安裝不良或許會干涉滑塊。
The radius of chamfering is less than or equal to 3.5mm. If chamfering is too large or protruding, oil stone and file should be selected in time to deal with it. Otherwise, poor installation of guide precision may interfere with slider.
直線導軌裝置基面鎖緊螺紋孔的加工。
Processing of thread holes for base locking of linear guide device.
開箱后直線導軌的查看。
Check the straight-line guide after opening the box.
查看直線導軌是否有合格證,有否碰傷或銹蝕,將防銹油清洗干凈,鏟除安裝外表的毛刺、撞擊突起物及污物等。
Check whether the straight-line guide is qualified, whether it is damaged or corroded, clean the rust-proof oil, remove burrs, bumps and dirt on the installation surface, etc.
滾珠絲桿、直線導軌發生磨損,將會導致精度失效,有必要更換維修,否則會嚴重影響到機械設備的生產功率。故應當仔細分析滾珠絲桿、直線導軌發生磨損的各種原因,這樣才干找到針對解決方案。
 
 
The wear of ball screw and linear guide will lead to the failure of accuracy. It is necessary to replace and repair, otherwise it will seriously affect the production power of mechanical equipment. Therefore, we should carefully analyze the causes of wear of ball screw and linear guide, so as to find solutions.
異物進入到了螺母滑塊內,將會與潤滑油混合在一起,然后形成翻滾溝槽阻塞形成損害。
When the foreign body enters the nut slider, it will mix with the lubricant and then form a rolling groove blocking to cause damage.
潤滑油里面的雜質沒有過濾干凈,有雜質混入導軌內部,或許潤滑的方式不良、選用的潤滑劑不正確或蛻變都會形成磨損。
The impurities in the lubricating oil are not filtered clean, and impurities are mixed into the guide rail. Perhaps bad lubrication, incorrect selection of lubricants or metamorphosis will lead to wear and tear.
因溫度變化所發生的冷凝水或是潤滑劑中添加劑的腐蝕性物質也會形成銹蝕,然后形成磨損。
The corrosive substances of condensate water or additives in lubricants caused by temperature changes also form corrosion and then wear.
以上狀況將會引起滾珠絲桿、直線導軌作業外表的粗糙和游隙的增加,較終導致絲桿導軌的失效。但只要是金屬零件,它的正常磨損是不可避免的,正常磨損是均勻并且緩慢的進行的,可以留意平時維護削減磨損延伸使用壽命。
The above conditions will cause the rough surface and the increase of clearance of ball screw and linear guide, and eventually lead to the failure of the lead screw. But as long as the metal parts, its normal wear is inevitable, normal wear is uniform and slow, you can pay attention to the usual maintenance to reduce wear and extend service life.

濟南共潤科技有限責任公司

篮球比分网即时比分直播